We found all the materials to build this shed at our local home center. Most of the construction is straightforward and requires only standard carpentry tools and a circular saw. For how to build the shed windows and door, you’ll also need a table saw, power miter saw and router. We used a Kreg pocket hole jig and pocket hole screws to assemble the door and windows. With a helper or two, you could have the platform and shell built in two or three days. Then expect to spend four or five more days completing the siding, trim, doors, windows and roofing.

The idea for this has been in my head for a while (and on a paper for a shorter while), but let’s face it: I need more DIY space — especially for tools and garden storage. The one-car garage I have is packed full all the time with the mower, gardening materials, woodworking tools, paint, and more. Even though I try as best I can to keep it organized(ish… meh) by cleaning it out once a year, that still means I spend a lot of time looking for the things I need in a very tight space (you would think losing things in a smaller space would be less frequent, but… nope).
Of all the different simple shed designs, this one uses simple stacked lumber siding in which each length of board is laid edge on to the one below it and nailed in place. While this design can be quite strong, unless you seal the gaps between each board with some form of caulking, it might let the rains come in. Once your little girl grows out of it, you can turn it into a dog house, or add plexiglass windows and a door to turn it into a storage shed.

A concrete base is the most common type of base for garden buildings and are relatively easy to build, but most people will hire a reputable builder to install the base. A concrete base must be installed in advance of receiving you garden building, this ensures the base has properly set before the building is installed. If the base has not properly set a build up of condensation can form within your new garden building.
I’ve always wanted to learn more about woodworking. Learn framing. Be better at picturing the insides of the walls I’m always messing with. Overall, I want to also increase my knowledge on the kinds of tools I don’t really use as much for interior DIYs (like a roofing nailer?!?! BRING IT ON!). I learned a little by volunteering in Habitat for Humanity events, but I know that there is still so much more fun stuff I could be doing and learning. So, after months of trying to think of where best to put it, what it might look like, the hoops I might have to jump through to get it, I’m going for it! I am building it from scratch (not using a shed-building kit), and I will share as I go, warts and all (and I’m sure, a few mistakes). 😃 😃 😃
You can use the backyard garden shed as a space for housing your lawnmower, planting supplies, pots, seeds, old furnishings, etc. On the other hand, you could even install a backyard garden shed as a tiny house the kids can play in. However, you choose to use your backyard garden shed, there are plenty of ways to incorporate the space into your garden scene! Here are some of the best ideas on how to use a backyard garden shed in your own garden.
It’s no surprise that most sheds are designed to be built with an on-grade foundation. This base is quick and easy to build, relatively inexpensive, and adaptable enough to accommodate all but the most severely sloping sites. In addition, the components are small and light enough to easily set into place and shift around, making it very easy to get everything square and level. Although it’s not technically a “permanent” foundation, an on-grade foundation, when properly built, will probably outlast the shed it supports.
Concrete starts to harden and set about two hours after it has been mixed, so it must be laid, tamped (packed down) and given its finish within that time. Divide large areas into bays or sections which can be completed one at a time before they begin to set. You can walk on the concrete after three days and remove the formwork after five days (but as always, check any product instructions for the mix you are using as there are rapid-setting options available).

Also square the frame by making sure diagonal measurements from opposite corners are equal. Then tack one corner to hold it square. Finally, nail the soffit to the roof frame with 6d galvanized box nails. We used 12-in.-wide fiber cement siding for soffit material. Mount an inexpensive carbide blade on your circular saw to cut the fiber cement. Set the roof panel aside and build the other half of the roof using the same techniques.


Are you against the idea of a treehouse because you fear for your kids’ safety? Then, here’s the solution. If you don’t want them to hate you ever since their childhood (they’ll have plenty of occasions later on), you’ll buy a nice shed and you will paint it to turn the construction into a beautiful playhouse for your children. The shed in this photo was actually turned into a playhouse for 2 little girls.
Now that the floor is completed you can assemble the wall frame on the leveled floor. You can build the wall frames using 2x4 lumbers. The top and bottom 2x4’s are called plates. Place the 2x4 wall studs 16-24 inches apart and nail through the plates and into the wall studs. While the wall frame is still on the ground you can install the siding to make it easier. When the wall is completed rise up and nail it into the floor.
This shed is so gorgeous it looks like some kind of fancy greenhouse. Technically, you probably could turn this shed into a greenhouse, although its primary purpose is to store things. It doesn’t really matter, though, when you have a shed that is this lovely. You could turn it into anything you want, and because of its beauty, you may want to just transform it into a recreational hall!
*Please note the content in this blog post is intended only to provide a summary and general overview on building a pallet bar. It is not intended to be comprehensive. You should refer to the instruction and safety manual of tools and paints you use and seek professional advice if unsure of how to execute the tasks before acting or relying on any of the instructions.
A concrete base is the most common type of base for garden buildings and are relatively easy to build, but most people will hire a reputable builder to install the base. A concrete base must be installed in advance of receiving you garden building, this ensures the base has properly set before the building is installed. If the base has not properly set a build up of condensation can form within your new garden building.
I am planning to build a 20 X 16 shed in my yard in Brandon, FL. I want to be able to pull my truck in to work on it at times. I will be putting it on a Wood deck platform. What it the best ideas for weight support for the 5K Lb. truck? IE: 2X6s, 2X8s what type f spacing is best and which direction should the joists be going in reference to the roll up door? And help would be appreciated.

Note: Here’s how we can help: 24hplans has team of highly-trained, professional architects and drafters who can prepare any kind of site plan in the shortest amount of time possible, so that you can easily obtain that building permit and get on with your project. Use the promotion code: 24hplans-20off to get a 20% discount off any package. — Please note this is a limited time offer, exclusive to the readers of our blog. This offer is not being advertised anywhere else.
This side shed is a great way to store simple stuff, such as the lawn mower or your garden tools. It almost blends into the scene with the toy beside it and the rich foliage next to it. It is unobtrusive but quite functional, as it will prevent so many tools from either rusting in the rain or being baked in the sun. Overall, these sheds can save you money since all of your garden essentials will be protected.
We found all the materials to build this shed at our local home center. Most of the construction is straightforward and requires only standard carpentry tools and a circular saw. For how to build the shed windows and door, you’ll also need a table saw, power miter saw and router. We used a Kreg pocket hole jig and pocket hole screws to assemble the door and windows. With a helper or two, you could have the platform and shell built in two or three days. Then expect to spend four or five more days completing the siding, trim, doors, windows and roofing.
×