Search the hashtage #vintagetrailers on Instagram and you'll discover some 80,000 images of big, small, and mid-sized aluminum travel trailers from roughly the 1950s to 1970s. You might find gleaming silver Airstreams at a lodging rental in Joshua Tree or parked temporarily at a campground near Yellowstone. One trend that hasn't lost steam is the backyard she-shed trailer escape, a dolled-up adult playhouse where women--or men--can escape for alone time or to hang out with friends and a bottle or two of wine. There's even a Vintage Trailer Magazine for enthusiasts. This vintage Aljo trailer rests in the backyard of a house in Pasadena, California.
If you have the do-it-yourself skills and an open timeframe, check out the various plans available online or for purchase. Make sure you thoroughly understand the instructions and actually have the ability and tools to do the job. Other sources for sheds include prefabricated buildings that you would order from a reputable company and kits. Some include pre-cut lumber that is shipped to your house. Before ordering, find out if additional milling, drilling, or cutting will be needed, along with necessary tools.
After laying out the 12 blocks, use a straight 2 x 4 and a 4-ft. level to ensure that all the blocks are level. Shim up any low blocks with strips of asphalt roofing, cedar shingles or 2-in.-thick concrete patio block. Next, form each front and rear band joist by nailing a 2 x 6 to a 2 x 8 mudsill. Set the mudsills on top of the blocks running across the front and rear of the shed. Cut a third 2 x 8 mudsill to fit along the tops of the center row of foundation blocks.
Thanks again for reaching out to us. I spoke with our engineering department and your servicing branch. Our sheds are designed for typical storage. Transforming the shed into a livable space voids the warranty. Unfortunately, we cannot facilitate your requests. If you have any other questions, feel free to give our branch a call at (678) 797-5402. Have a great day!
Disclaimer: Please note that this guide is intended to present general information regarding the subject. All information indicated are representative and not exhaustive, which means that the results may vary depending on your item, its size, complexity and other circumstances. This is only advice and we do not accept responsibility for any problems you may have whilst following this guide, it is only a representation and not a definitive guide. When in doubt, please ask your manufacturer before proceeding.
If you do not require a shed floor it would be advisable at this stage to add a damp proof membrane, this can be laid on top of the hardcore ready for the concrete. A concrete mix of 5 parts ballast and 1 part cement should now be mixed and poured into the area, enough concrete should be poured so that it is just proud of the formwork. It can now be tampered down level and flat using a straight piece of solid timber. The result should be a smooth level concrete base - the ultimate shed base.
While every effort has been made to ensure the accuracy & effectiveness of the information displayed on this website, the Ugly Duckling House is for entertainment purposes only. All tutorials and demonstrations are not intended to be professional advice (nor substitute as such), and I make no guarantees as to the procedures and information here. Creating with my suggested methods, materials, and tools is under your own risk. Please ensure you are following proper guidelines with anything used, and seek professional advice if you don’t know how to do something! Read my complete disclosure here.
For this reason, I am planning to run utilities to the building including natural gas, water, sewer, etc. in order to locate the sewer line for proper flow (connection location) I was hoping to have a standard footer with crawl space installed and attached the building on top of it (just like a house). This way I could access the utilities by removing sections of the floor so I could run the sewer line (and other utilities) to exact areas of the building. Is it possible to have the building constructed/attached on top of this type of footer system?
Since it’s made out of plastic, there’s nothing glamorous about this shed’s appearance. Also, if you plan on storing expensive stuff in this shed, you should perhaps think about other options, because this one is a low security shed. Although you can install a hard to break lock, the thief can still cut through the plastic with ease, thus rendering your lock useless.
Using Figure C as a guide (in project pdfs below), chalk lines on the floor to indicate the inside edges of the walls. These lines provide a reference for straightening the bottom plate of the walls after the walls are standing. Cut the top and bottom wall plates and mark the stud locations on them (Figures D – G, also in project pdfs). Build the side walls (Photo above) of the pub shed. Then build and stand the front and back walls. Brace them temporarily.
The roof truss can be built using 2x4 or 2x6 lumbers. There are different ways to build the truss, the most common is cutting out the rafters and assembling them using gussets. The easiest way to build the roof truss will be using plans. The other option will be to lay the 2x4’s or 2x6’s on the level floor set them how you want your roof and make a template. Once you are happy with the look of your template you can build the rest.
This charming backyard garden shed has been transformed into a beautiful art studio. Not only is the space relaxing, but also the fact that it was constructed from a shed makes the space much more affordable than having to go and build and office space from scratch. Once you have the groundwork done and your shed layout, you can decorate it any way you choose to make it uniquely you.
Are you against the idea of a treehouse because you fear for your kids’ safety? Then, here’s the solution. If you don’t want them to hate you ever since their childhood (they’ll have plenty of occasions later on), you’ll buy a nice shed and you will paint it to turn the construction into a beautiful playhouse for your children. The shed in this photo was actually turned into a playhouse for 2 little girls.
Although skids are often set directly on the ground, I prefer to lay them on a bed of gravel. The stone creates a very stable base that’s not likely to settle or wash away. Begin by laying the skids in position on the ground, then mark around each one using spray paint or flour sprinkled from a can. Move the skids out of the way, then use a flat shovel to remove the sod and about 2 in. of soil from the marked areas. Check the excavated areas to make sure they’re close to being level. If they’re not, remove a little more soil from the high spots. Next, add 3 in. to 4 in. of gravel. Compact the gravel with a hand tamper or gas-powered plate compactor, then replace the skids.
Without the correct base erecting a shed can prove very tricky. It is extremely important that all garden buildings are constructed on a firm and level base which is constructed from the correct, durable material. Assembling the base incorrectly can lead to future deterioration of the product such as doors dropping out of square, thus becoming complicated to use or causing a water leakage.
When you nail on the siding, make sure it overhangs the framing on each side by 3-1/2 in. and that you’ve trimmed off the top corner to follow the slope of the angled top plate (Photo 2). Attach the siding with 2-in. galvanized or stainless steel ring-shank siding nails placed 8 in. apart along studs and 6 in. apart along the edges of the sheets. You’ll have to nail blocking between the studs to support the top edge of the siding and the Z-flashing.