The composition and design of our plastic shed base range may seem a little strange at first. Each panel is secular in design with the intention of certain panels being filled to add further support to the shed above. Typically, with other types of shed base, because they’re solid, a layer of air is trapped between the shed base and the bottom of the shed. This can quickly become warm and moist and, if left, could cause a severe damp problem that’ll leave your shed rotting from the base up.

There are several ways to economize when building a shed: Install three-tab roof shingles instead of architectural shingles, or use grooved-plywood siding in place of cedar bevel siding. But don't ever skimp on the building materials used for the floor frame or plywood floor deck. I can't tell you how often I've walked into a shed and found the floor to be dangerously spongy. One building in particular had a floor so badly rotted it felt like one of those inflatable moonwalk attractions you see at carnivals.


4. Lay out your 4" x 4" skids properly spaced and lined up on your foundation, making sure they are level. Set the floor frame on top of the skids and measure the diagonals to make sure it's square. At this point, toe nail all joists to your skids using 16d common nails. The joists which fall at the 4', 8', and 12' lengths along your skids should be measured before nailing to make sure they are nailed exactly on center at those distances. This way,
We’re using tongue-and-groove LP ProStruct Flooring with SmartFinish for the shed floor. Fasten the first sheet in the back corner with construction adhesive and deck screws. Finish the row with a half sheet. Then start with a full sheet from the opposite end so the seams between sheets are staggered. The photo above shows how we installed the flooring. Learn more in-depth instructions for how to install flooring here.
These sheds are perfect for small yards where space is scarce. If you plan on storing large items inside, make sure to install double doors. On the other hand, if you want to design it like a very small office, one door is enough. Lean-to sheds are generally used for storing tools like nails, screws, electric drills, gardening equipment etc., basically anything that fits. Lean-to sheds can be placed in close proximity to your house or other existing structure.
If the building site is high and dry, you can set the blocks directly on the ground. However, if there’s any chance that rain runoff will occasionally drain under the shed, you’ll need to use a shovel to remove a patch of grass under each block, compact the soil with a hand tamper, then cover the exposed dirt with 2 in. or 3 in. of gravel before setting the blocks. The gravel bed will ensure that the soil beneath the blocks won’t wash away or become soggy.
Next, you will need to insert wooden shuttering or formwork around the edges of your excavated area. This will need to be made from 6"x1" timber and screwed or nailed into position. If need be, wooden pegged to form a square, level solid formwork to hold back the hardcore and concrete (in the next step). The reason for the original excavation to be 2" bigger all the way around is to take into consideration the wooden frame, you will now have an internal area of 8"x6". If you decide to use thicker timber you will need to take this into consideration at the stringing out stage. 

Are you against the idea of a treehouse because you fear for your kids’ safety? Then, here’s the solution. If you don’t want them to hate you ever since their childhood (they’ll have plenty of occasions later on), you’ll buy a nice shed and you will paint it to turn the construction into a beautiful playhouse for your children. The shed in this photo was actually turned into a playhouse for 2 little girls.
The idea for this has been in my head for a while (and on a paper for a shorter while), but let’s face it: I need more DIY space — especially for tools and garden storage. The one-car garage I have is packed full all the time with the mower, gardening materials, woodworking tools, paint, and more. Even though I try as best I can to keep it organized(ish… meh) by cleaning it out once a year, that still means I spend a lot of time looking for the things I need in a very tight space (you would think losing things in a smaller space would be less frequent, but… nope).
Now that the floor is completed you can assemble the wall frame on the leveled floor. You can build the wall frames using 2x4 lumbers. The top and bottom 2x4’s are called plates. Place the 2x4 wall studs 16-24 inches apart and nail through the plates and into the wall studs. While the wall frame is still on the ground you can install the siding to make it easier. When the wall is completed rise up and nail it into the floor.
This is a very beautiful shed and it matches the main house that was originally designed by J. Merrill Brown back in 1887. In fact, it’s like a miniature version of the main residence. The colors chosen for the exterior are simple but beautiful and the roof is charming as well. It has a very chic look and it’s like an updated, more elegant version of the shed presented above.
Studio Shed’s design philosophy does not stop at good looks. Our Signature Series and Summit Series models are designed with efficiency and performance in mind. Unlike traditional backyard sheds, we use the highest quality materials available to create spaces that perform to residential standards and meet the most stringent building codes throughout the country. A Studio Shed is an extension of your home, thoughtfully designed to maximize space, functionality, and comfort.

Once you have a pile of pallet wood start by laying bits of wood on the floor. If you have different sizes and shades then mix them up to get a great effect. Start in the top corner and screw the boards in place using an electric screwdriver with screws long enough to go through the pallet wood and floor of the shed.  You’ll need to cut some pieces to size so use the tape measure to mark the wood then cut using a saw of choice.  Once the floor is down then line all the walls apart from the doors and eaves.


There are several ways to economize when building a shed: Install three-tab roof shingles instead of architectural shingles, or use grooved-plywood siding in place of cedar bevel siding. But don't ever skimp on the building materials used for the floor frame or plywood floor deck. I can't tell you how often I've walked into a shed and found the floor to be dangerously spongy. One building in particular had a floor so badly rotted it felt like one of those inflatable moonwalk attractions you see at carnivals.
If you do not have a lot of bulky gardening equipment, but would still like to protect and store your standard tools, acquiring a smaller shed may be the best bet for you. This convenient space will provide shelter for all the gardening essentials and will help you keep all your tools organized. What a great feeling to know that all your tools are going to be organized within the same space and you do not have to go out and hunt for them all.
When building a solid-concrete block foundation, it’s important that all the blocks be level. However, it’s equally important that the blocks in each row be perfectly aligned. The best — and fastest — way to line up the blocks is with a taut string. Install the first and last block in each row. Then stretch a length of mason’s line along the edge of the two end blocks and use it as a guide to set the intermediate blocks..
Although local building regulations may differ from city to city and county to county, there are some general rules that indicate whether you need a permit or not. However, the easiest way to find out is to take a look at your local building department regulations. Also, note that in many cases it may be necessary to provide a site plan to obtain the permit from your city hall or township. You can get a custom site plan drawing prepared for your property in 24 hours by our team of experienced architects and drafters. Use the promotion code: 24hplans-20off to get a 20% discount off any package. — Please note this is a limited time offer, exclusive to the readers of our blog. This offer is not being advertised anywhere else.
Each truss is made up of two 2 x 4 rafters and one 2 x 4 ceiling joist. The three boards are joined together with 1/2-in. plywood gussets. To speed up the assembly process, build all the trusses on the shed floor before erecting the walls. Start by cutting all the rafters to length with a 40° angle at one end of each. Cut 2 x 4s to 10 ft. long for the bottom chords of the trusses. Also, cut all of the plywood gussets.

After laying out the 12 blocks, use a straight 2 x 4 and a 4-ft. level to ensure that all the blocks are level. Shim up any low blocks with strips of asphalt roofing, cedar shingles or 2-in.-thick concrete patio block. Next, form each front and rear band joist by nailing a 2 x 6 to a 2 x 8 mudsill. Set the mudsills on top of the blocks running across the front and rear of the shed. Cut a third 2 x 8 mudsill to fit along the tops of the center row of foundation blocks.
4. Lay out your 4" x 4" skids properly spaced and lined up on your foundation, making sure they are level. Set the floor frame on top of the skids and measure the diagonals to make sure it's square. At this point, toe nail all joists to your skids using 16d common nails. The joists which fall at the 4', 8', and 12' lengths along your skids should be measured before nailing to make sure they are nailed exactly on center at those distances. This way,
Thank you for visiting our blog. We always recommend finding some way to allow air to flow under the shed. Especially if you live in an area that is humid and receives a lot of rainfall. Without air flow, water will often just sit there and soak into the wood. That is our suggestion. Feel free to give us a call if you have any other questions at 855.853.8558. Have a great day!
Mark the position of the rafters along the beams at 16-inch centers and carefully nail them in place. We even went so far as to set each nailhead to firmly pinch the rafter down against the beam. We nailed the front fascia in place and moved on to the skip sheathing for the roofing. Note that two pieces of sheathing are nailed on at the peak and at the base. The rest are spaced evenly between them.
Thank you for visiting our blog. Concrete isn’t the only method to give positive results over time for a foundation and doors working properly. Using gravel can have positive results over time compared to concrete. Make sure the gravel is packed down. And we recommend using solid masonry blocks on top of gravel with no more than 48” spacing between blocks. I hope that helps your project!
Garden sheds are very common and that’s because of their multiple functionalities. They can be used for storage for all the items you no longer have room for in your house but mostly for garden supplies and tools. Also, they commonly used for hobbies. They’re like a mini-home for all your collection items and memorabilia, like a sanctuary for personal items. Moreover, garden sheds also make great workshop spaces. And since their functionality varies from person to person and from type to type, so does their design.
4. Lay out your 4" x 4" skids properly spaced and lined up on your foundation, making sure they are level. Set the floor frame on top of the skids and measure the diagonals to make sure it's square. At this point, toe nail all joists to your skids using 16d common nails. The joists which fall at the 4', 8', and 12' lengths along your skids should be measured before nailing to make sure they are nailed exactly on center at those distances. This way,
Even though garden sheds are typically one-story structures, there’s no rule that says you can’t change that. Take this shed for example. It’s a two-level structure and the second story is a quiet and relaxing area, like a mini-bedroom. In this case, both the interior and exterior designs are elegant. The shed is infused with natural sunlight coming through the dormer window upstairs and the checkerboard tile floor adds a touch of style as well.
This garden hut shed is practically growing into the scenery. The hut is sheer nature, as depicted by the garden growing off the roof of the structure. This shed has undoubtedly been in this surrounding for a while, but that does not diminish the function of it. If anything, the charm of this shed surpasses the time this tiny shed has probably spent on this hillside.
There may be a pile of wood in the backyard that looks like it should be disposed of. However, with a little care and creativity, it can be made into a rustic looking shed that fits in a backwoods or backyard garden area. A little creative piecework, and cleaning old wood can become a beautiful piece of art. A coat of clear coat paint could bring out the aged beauty and protect the wood for years. IDEA: Repurpose your old wood and turn it into a piece of art in your garden.
If you don’t already have a garden shed, but wish you did, take a look at the sheds shown here. Whether you want a simple utilitarian structure for storing tools and equipment, a workspace for potting, a playhouse for kids, a fanciful focal point for outdoor living, or something in between, you’re sure to find inspiration in these photos posted by members of our sibling site FineHomebuilding.com. Click on the links below to see more photos of these structures.
Do not make the mistake of not building your own shed because you have never done it before. With the right shed plans you will get the same results the experts get. Begin by choosing plans you feel comfortable with and know you can follow along. Simply follow the steps provided, measure correctly, and in no time you will construct your own shed. Study the building guide to get familiar with all the steps and to get to know the names of all the parts.
Each truss is made up of two 2 x 4 rafters and one 2 x 4 ceiling joist. The three boards are joined together with 1/2-in. plywood gussets. To speed up the assembly process, build all the trusses on the shed floor before erecting the walls. Start by cutting all the rafters to length with a 40° angle at one end of each. Cut 2 x 4s to 10 ft. long for the bottom chords of the trusses. Also, cut all of the plywood gussets.
×