This whole backyard space seems well put together thanks to the matching wood elements and complementing plant life. This is a great way to incorporate a storage shed into the garden space that does not stick out or look like an actual storage shed. In this case, the storage shed is only made more beautiful by all these complementing elements that work in conjunction.
Set up a levelled formwork. This involves measuring, cutting and fitting timber to the shape of the base in order to contain the concrete. Check diagonal measurements to ensure the formwork is square and level as this will determine whether your shed base is 100% sturdy. Next, spread a layer ofwell-compactedd hardcore (all-in ballast or crushed gravel) and cover with a liberal amount of sand. This needs be well compacted and flattened down, preferably with a compacting tool or roller.
Concrete starts to harden and set about two hours after it has been mixed, so it must be laid, tamped (packed down) and given its finish within that time. Divide large areas into bays or sections which can be completed one at a time before they begin to set. You can walk on the concrete after three days and remove the formwork after five days (but as always, check any product instructions for the mix you are using as there are rapid-setting options available).
Omit the bird’s-mouth from four rafters and use these on the ends. Cut the 2x4s for the ridge and subfascia to length and mark the rafter positions on them. Line up the rafters with the marks and nail through the ridge and subfascia with 16d nails to secure them. When the roof frame is complete, line up the subfascia with the chalk line on the platform and tack it in three or four places with toe screws to hold the frame straight while you install the soffit.

Use dimensions from Figure C (in Additional Information below) to snap lines for the peak. Then cut 2x4s to fit inside the lines and toe-screw them to the plywood to hold them in place while you fill in the center studs (Photo 1) and nail on the siding (Photo 2). Toe-screw from the outside so the screws will be accessible after the siding is installed.
This tiny shed looks a little more like an old English phone booth than a shed thanks to the glass door. But it definitely looks bigger on the inside. If you look closely, the walls of this shed appear to have been made from exterior grade doors. Not only can this save you a lot of money in supplies, it looks very cool and should be very strong. You can pick up used doors at any building salvage store or your local Habitat for Humanity Store.
Each truss is made up of two 2 x 4 rafters and one 2 x 4 ceiling joist. The three boards are joined together with 1/2-in. plywood gussets. To speed up the assembly process, build all the trusses on the shed floor before erecting the walls. Start by cutting all the rafters to length with a 40° angle at one end of each. Cut 2 x 4s to 10 ft. long for the bottom chords of the trusses. Also, cut all of the plywood gussets.
The front and back gable ends are covered with panels that resemble cedar shakes. After installing a metal drip cap over the 1×2 that caps the wide trim board, install the shakes according to the manufacturer’s instructions (Photo above). Follow the manufacturer’s instructions for details about panel placement and how much caulk space to leave between the panels and the trim.
This is one of the bigger (and more costly) DIYs I’ve ever wanted to do, so I’m going to have some first-time learning curves ahead. Also, obviously, it’s something I’ve had to save up for. If you’ve noticed the increase in my sponsored projects on the site over the last few months, this is one of the main reasons I’ve taken them on (the summer is usually when I wind up working with more sponsors, so I wanted to funnel some of that to immediately start planning for this!). I’ve already seen what the kinds of costs are to have one custom built by ordering, so I’m hoping the DIY is also going to be more budget-friendly.
Hendy Michelle from the website Vkool.com says, “Ryan Shed Plans is really a useful guide for woodworkers who really want to start a woodworking business. The e-guide includes many useful techniques to build a lounge chair and outdoor fireplaces. Additionally, the system also supplies blueprints, schematics and intricate illustrations of different shed plans. In other words, when ordering this program, people will have 60 days to decide if they want to keep the Ryan Shed Plans program or get their money back.”
A wooden base is sufficient for most smaller sheds. It’s basically a simple wooden frame, strengthened with crossbeams, onto which you build your shed. Check the weight of your shed and its contents. If you intend to install a large garden building - anything larger than 10 x 8 feet - or store a lot of heavy equipment, consider a paving slab or concrete base instead.
Connect three windows to form the window assembly for the side wall (Figures R and U). Use a pair of 2x4s as spacers between each window. Screw through the window frames into the spacers to hold the windows together. Tip the triple window assembly into the window opening. Shim under the windows until about 3/8 in. of the top frame is exposed on the outside. Shim between the studs and the window frame to level and plumb the window unit and to adjust the frame until there’s a consistent space between the window frame and the sash. Make sure the window frames are flush to the siding. Then screw through the window frames into the studs to hold the windows in place. We added Stanley Storm Window Adjuster hardware to the windows to hold them open and to lock them.
This tiny shed looks a little more like an old English phone booth than a shed thanks to the glass door. But it definitely looks bigger on the inside. If you look closely, the walls of this shed appear to have been made from exterior grade doors. Not only can this save you a lot of money in supplies, it looks very cool and should be very strong. You can pick up used doors at any building salvage store or your local Habitat for Humanity Store.
This open concept garden shed almost looks like a farmhouse. The open area would be perfect as a gathering area for guests or partygoers for your next backyard soiree. The super cute furnishings make this space absolute charming and it would be hard to pass up the opportunity to sit in this adorable, tiny space. This is a great space to utilize storage and double as an entertainment venue for later.
I really like the 16 x 16 Aspen and I’m currently installing my foundation and slab with a tentative purchase intent with your company. Our code here is, maximum of 256 sq. ft. shed without a permit. I’ve excavated -2′ around the perimeter and – 6″ for the pad. Right now I’m at that point of decision of concrete footer or not. I can fill my footer area with compacted 30D stone, then level the pad to grade or I could form and pour these footers which will cost a lot more bennies. I plan to frame the 16 x 16 pad for 6″ of concrete and call it a day. A few questions please; Will compacted stone under a concrete pad be sufficient for your shed? Can the shed be built without the floor in the quote if I have the concrete pad? What exact dims should that concrete pad be for your 16×16 Aspen? Thanks for your help, now back to work!
This shed studio is the perfect place for relaxing, getting some work done, or even living in! Tiny homes are all the rage these days, and what better way to construct a tiny home than utilizing a refurbished garden shed. Not only is the space so cost-effective, but it can really be a great little space if you know how to work with the area well. It could turn out to be a fun project!
I’m looking at putting a 10 x 12 shed in our back yard (Michigan). I’m wondering what would be recommended – if anything – for a base. It looks like, from the installation process photos, that the builder will assemble the foundation and can put that directly onto the grass. Our ground is level enough – within the 6″ required – so I don’t think that would be an issue. It sounds like – from what i am reading – that I wouldn’t NEED to do anything to prepare in terms of putting down stone or anything. Is that correct?
The roof panels are heavy and a bit awkward, so round up three strong helpers for this part of the job. Move the panels into position and lean them against the front and back walls. Then set up ladders inside the building for two helpers and push one of the panels up to them. Slide the panel up the roof until the bird’s-mouths drop over the top plate of the wall.
×