If your prehung door has exterior trim, pry it off. The wide trim board running around the shed, under the soffit, will take the place of the top door trim. Place the door in the opening to check the fit. The top doorjamb should rest against the wide trim board. Use wooden or composite shims between the side jambs and the 2×4 framing to square the door frame. Place shims behind each hinge and at the top, middle and bottom of the latch side. Adjust the shims until there’s an even space between the door and the doorjambs on the top and sides. Then drive screws through the doorjambs into the framing at the shim locations to secure the door.

If there’s even the slightest chance that you may someday want to move your shed to another location, make the job easier by modifying the skids before you set them in place. Start by trimming off the bottom corners of the skids at a 45-degree angle so they’ll slide more easily over the ground. Also, bore a 1 1/2-in.-dia. hole about 4 in. from each end. That way, you’ll have a convenient place to hook up a tow chain or steel cable.


You can make shelves using blocks that are left over when you dismantle the pallets and you could use left over pallet wood or ply wood.  I used some old decking off cuts. Drill two blocks on to the wall – good to use a spirit level to get these straight, then lay the pallet wood/ply wood/decking cut to size on top and screw the shelf onto the blocks.
I am building a 20 a 20 foot floor for a workshop in a space under my house so the area is always dry. There is already a crushed stone floor. Can I dig a trench, fill it with stone and lay 4×4’s or 2×4’s on top of it for a foundation? If so, would they have to be pressure treated? Do I even need crushed stone if use pressure treated wood on top of dirt Would concrete blocks or pavers with 2×6 headers be a better idea? Which is the least expensive way to go?
This small backyard shed is a minimalist approach to a larger storage facility. Its classic design serves both in function and as a great element to have in a backyard setting. The shed looks sleek, modern and interesting. It does not look like a standard storage shed, so if you were trying to disguise the shed as something else, this would be a great design to execute that.

Award Winning Designer, Candace Osmond has been in the industry for over a decade. She studied Interior Decorating & Design and is also an accomplished writer and multi-published author. When she's not typing away from the comforts of her desk, Candace can be found travelling to warm destinations, tending to her garden, or enjoying the outdoor haven that is her backyard. Candace currently resides in the breathtaking Maritimes of Eastern Canada with her husband, two beautiful kids and one slobbery bulldog.
This is one of the bigger (and more costly) DIYs I’ve ever wanted to do, so I’m going to have some first-time learning curves ahead. Also, obviously, it’s something I’ve had to save up for. If you’ve noticed the increase in my sponsored projects on the site over the last few months, this is one of the main reasons I’ve taken them on (the summer is usually when I wind up working with more sponsors, so I wanted to funnel some of that to immediately start planning for this!). I’ve already seen what the kinds of costs are to have one custom built by ordering, so I’m hoping the DIY is also going to be more budget-friendly.
You can make shelves using blocks that are left over when you dismantle the pallets and you could use left over pallet wood or ply wood.  I used some old decking off cuts. Drill two blocks on to the wall – good to use a spirit level to get these straight, then lay the pallet wood/ply wood/decking cut to size on top and screw the shelf onto the blocks.
It can be easy to get excited and overestimate your DIY abilities when you start a new project. The passion and excitement makes you want to dream big and get creative. But blindly following your imagination can be a step in the wrong direction. If you’re a newbie to DIY woodworking, then you’ll probably want to keep it simple. Otherwise you run the real risk of ending up with a sub par build or even having to rebuild it altogether.
×